What is the introduction of pyrolysis?

Author: wenzhang1

Aug. 19, 2024

What is Pyrolysis?

What is Pyrolysis?

If you are looking for more details, kindly visit our website.

Introduction     Our Research     What Is Pyrolysis?     Bio-Oil     Researchers

Facilities     Our Partners     Publications     In The News     Links

 

What Is Pyrolysis?

 

Biomass

Lignocellulosic biomass is the most abundant renewable carbon source on Earth.  Available biomass sources include forest residues, crop residues, purpose grown energy crops (e.g. grasses), animal wastes and food wastes.  These materials are the fibrous structural parts of plants and are largely made of cellulose, hemicellulose and lignin.  Compared with so called 1st generation bio-feedstocks such as sugars, starches and vegetable oils, nature has made these parts of the plants difficult to deconstruct to chemical building blocks, making utilization of this carbon source a challenge for scientists and engineers.   Biorefineries are facilities where biomass is converted to a variety of products.  Our target products included advanced hydrocarbon biofuels that are indistinguishable from fossil-based gasoline, diesel or jet fuels along with bio-based chemicals and materials.  Technologies need to be developed to more efficiently convert this renewable carbon source so that renewable bio-products from biomass can be made economically competitive with those produced from fossil resources.

 

Pyrolysis

Pyrolysis is one of the technologies available to convert biomass to an intermediate liquid product that can be refined to drop-in hydrocarbon biofuels, oxygenated fuel additives and petrochemical replacements. Pyrolysis is the heating of an organic material, such as biomass, in the absence of oxygen.  Biomass pyrolysis is usually conducted at or above 500 °C, providing enough heat to deconstruct the strong bio-polymers mentioned above.   Because no oxygen is present combustion does not occur, rather the biomass thermally decomposes into combustible gases and bio-char.  Most of these combustible gases can be condensed into a combustible liquid, called pyrolysis oil (bio-oil), though there are some permanent gases (CO­2, CO, H2, light hydrocarbons), some of which can be combusted to provide the heat for the process.  Thus, pyrolysis of biomass produces three products: one liquid, bio-oil, one solid, bio-char and one gaseous, syngas.  The proportion of these products depends on several factors including the composition of the feedstock and process parameters.  However, all things being equal, the yield of bio-oil is optimized when the pyrolysis temperature is around 500 °C and the heating rate is high ( °C/s) fast pyrolysis conditions.   Under these conditions, bio-oil yields of 60-70 wt% of can be achieved from a typical biomass feedstock, with 15-25 wt% yields of bio-char.  The remaining 10-15 wt% is syngas.  Processes that use slower heating rates are called slow pyrolysis and bio-char is usually the major product of such processes.  The pyrolysis process can be self-sustained, as combustion of the syngas and a portion of bio-oil or bio-char can provide all the necessary energy to drive the reaction. 

  

Schematic of the Fast Pyrolysis Process.

 

 

Bio-oil is a dense complex mixture of oxygenated organic compounds.  It has a fuel value that is generally 50 - 70% that of petroleum bases fuels and can be used as boiler fuel or upgraded to renewable transportation fuels.  The bio-oil&#;s composition makes it thermally unstable and therefore difficult to distill or further refine, making additional research on producing higher quality bio-oil necessary.  However, its density is > 1 kg L-1, much greater than that of biomass feedstocks, making it more cost effective to transport than biomass.   Therefore, it&#;s is possible to envision a distributed processing model where many small scale pyrolyzers (farm scale) covert biomass to bio-oil which is then transported to a centralized location for refining.  To test this hypothesis, our group developed and constructed a mobile one-ton per day pyrolysis demonstration unit based on a reactor design called the combustion reduction integrated pyrolysis system (CRIPS). The CRIPS unit can produce bio-oil on location and can perform fast or catalytic pyrolysis to produce partially deoxygenated bio-oil.

  ARS&#;s Mobile Combustion Reduction Integrated Pyrolysis System (CRIPS)

Furthermore, the bio-char produced can be used on the farm as an excellent soil amender that can sequester carbon.  Bio-char is highly absorbent and therefore increases the soil's ability to retain water, nutrients and agricultural chemicals, preventing water contamination and soil erosion. Soil application of bio-char may enhance both soil quality and be an effective means of sequestering large amounts of carbon, thereby helping to mitigate global climate change through carbon sequestration.  Use of bio-char as a soil amendment will offset many of the problems associated with removing crop residues from the land.

 

Our Project

Our core project at the Eastern Regional Research Center current has four main objectives dedicated to making pyrolysis and biodiesel based biorefineries economically competitive.  They include:

  1. Develop thermochemical and/or catalytic, carbon efficient biomass and waste plastic conversion processes to produce bio-oils and bio-gas containing fractions suitable for use towards advanced commercially viable bio-fuels (jet, diesel, and gasoline carbon ranges).

  2. Develop pre- and post-process thermo-catalytic technologies to produce renewable chemicals and biocarbon materials from biomass, biochar, lignin and bio-oils.

  3. Identify and develop new feedstocks and technologies to produce biodiesel, renewable hydrocarbon diesel and biojet fuels from fats and oils.

  4. Accurately estimate the economic values of thermolysis conversion processes to produce bio-based fuels and chemicals.

 

Our approach to developing commercially viable pyrolysis based biorefineries is summarized in the Figure above.   We are developing catalytic pyrolysis technologies where a catalyst is used to reduce the oxygen content of the bio-oil to produce stable, low or mid-level oxygen content bio-oil that can undergo separation processes such as distillation to sperate fractions to be used for various refining processes to produce renewable chemicals in addition to biofuels. We are also developing replacements for fossil based industrial carbons such as coke and pitch that can be used in heavy carbon emitting industries such as aluminum smelting. Furthermore, we are tackling the plastic waste problem by considering waste plastic, especially the very common polyolefins, as a potential source of cheap hydrogen making up for the inherent hydrogen deficiency in biomass. Our preliminary results indicate that co-pyrolysis of biomass with plastic waste over a catalyst can increase the carbon conversion efficiency to valuable aromatic hydrocarbons.

 

 

 

 

 

 

 

 

Introductory Chapter: Pyrolysis

In comparison with other treatment processes such as gasification, pyrolysis produces in general fewer air emissions, lower emission of nitrogen and sulfur oxides, less CO 2 generation, less dust emission and no emission of dioxin inside the pyrolyzer due to the pyrolysis with deoxidized hydrocarbon gas.

Pyrolysis can also be used for all types of solid and liquid products and can be easily adapted to changes in feedstock composition.

The technology is relatively simple and can be made compact and lightweight. Applications of pyrolysis processes range from large-scale industrial applications where high temperatures are used to smaller-scale operations, even portable biomass conversion units, where the temperatures may be much lower. Mobile pyrolysis units for the production of liquid and solid fuels have been designed for the treatment of timber and lumber mill and other agricultural wastes. The pyrolysis units are built on trailers and consist of four basic groups: feed preparation machinery, a fluidized bed pyrolysis vessel, product separation equipment and an onboard gas turbine electrical generation system [ 9 ].

A catalyst may be used in catalytic pyrolysis processes to improve the yield and lower the temperature and/or time of reaction. Aromatic hydrocarbons such as benzene, toluene and xylenes may be directly produced by catalytic pyrolysis of biomass [ 7 , 8 ].

Fluidized and fixed-bed reactors are mostly exterior-heating pyrolysis reactors where heat is transmitted from the exterior surface to the interior of the material. In fluidized bed reactors, fluidization increases mixing and interaction leading to efficient heat transfer, uniform temperatures, improved reaction rates and higher yield of bio-oil. On the other hand, interior heating is utilized in microwave-assisted pyrolysis with high energy effectiveness and the production of uniform products. Unlike traditional heating, microwave heating provides quick quenching of the pyrolysis vapors, which avoids secondary decomposition reactions of the primary products.

Reactor type is crucial for the efficient production of pyrolysis oil. Reactor types include packed or fixed-bed reactors, rotary kiln reactors and fluidized bed reactors. Fluidized bed reactors in particular, such as the auger, bubbling fluidized bed reactor and the circulating fluidized bed reactor, are highly efficient for the large commercial-scale production of pyrolysis oil [ 6 ].

While feed particle size may not greatly affect pyrolysis product distribution, larger particle size tends in general to increase the liquid yield at a higher temperature range. Smaller particle sizes on the other hand favor the internal heat transfer within the particles. In fluidized bed reactors, the particles must be greater than a minimum, in order to avoid entrainment of fines, particularly where the material has a low density [ 5 ].

Pyrolysis may be carried out at atmospheric or higher pressure or in vacuum where uncontrolled combustion is avoided. In practice, however, pyrolysis is mostly carried out at atmospheric pressure as creating a vacuum or high pressure drastically increases the cost of process equipment. Operation under high pressures results generally in greater yields of biochar and gases, while lower pressure or vacuum results in increased production of liquid products.

If you are looking for more details, kindly visit Sihai Energy.

Related links:
Crusher

The rate of heat transfer also influences the product distribution. In fast pyrolysis at lower temperatures, higher heating rates and small residence times favor liquid yield as the cracking of larger molecules to produce gaseous products is hindered. Liquid yield is also favored by immediate and rapid quenching which is often used to maximize the production of liquid products by condensing the vapors and gaseous molecules. Intermediate pyrolysis in screw reactors with longer residence time (minutes vs. seconds) can also be used for bio-oil production. In this process, two condensates are usually obtained, an aqueous phase and an organic phase defined as bio-oil. Although the yield of bio-oil is lower compared to fast pyrolysis, the bio-oils produced from intermediate pyrolysis are more stable, contain less oxygen, and have lower molecular weight substances, and the process is easier to control [ 4 ]. Slow pyrolysis, on the other hand, can be used to maximize the yield of solid char. This process requires slow pyrolytic decomposition at low temperatures.

Pyrolysis reactions typically occur at temperatures between 400 and 800°C. As the temperature changes, the product distribution can be altered. Lower pyrolysis temperatures usually produce more liquid and solid products, while higher temperatures favor the production of more gases as a result of more powerful thermal cracking reactions. The pyrolysis temperature has also a significant effect on the properties of the pyrolysis products. The calorific value of the pyrolytic oil, for example, increases mostly with increasing temperature.

Pyrolysis is an endothermic process. Determination of the overall energy balance and the thermal efficiency of the process is a fundamental step in designing an efficient pyrolysis reactor. The use of renewable energy or solar-thermal power to drive pyrolysis could make the process more economical and carbon neutral [ 2 , 3 ].

Pyrolysis is mostly applied to organic materials. It is basically a carbonization process where an organic material of high molecular weight is decomposed or cracked to produce a solid residue with high (or higher) carbon content and some volatile products. As is well-known, any organic matter can be carbonized or made to lose progressively its atoms other than carbon to become an artificial carbon material or &#;carbon&#;. In addition to organic materials, pyrolysis can be applied in certain cases to inorganic materials and to water and aqueous solutions.

The end products of pyrolysis include solid residual coproducts and ash, noncondensable gases and condensable liquids known variously as pyrolysis oil, pyrolytic oil, bio-oil or tar. The type and yields of the pyrolysis products depend for the most part on the type of material treated. The pyrolysis end products can also be controlled by optimizing pyrolysis parameters such as temperature, heating rate, residence time, pressure, feed particle size and type of reactor. For example, the production of bio-oil through pyrolysis, which is a thermodynamically nonequilibrium process, requires only a short residence time in a high-temperature zone followed by rapid thermal quenching. In some pyrolysis processes, a product that is up to 80% liquid by weight can be produced.

Pyrolysis is basically a thermal decomposition process where a raw material of high molecular weight is decomposed or cracked to produce primary volatiles. The primary thermal decomposition and dehydrogenation reactions are accompanied in general with secondary polymerization and isomerization reactions of the primary volatiles. The extent of the secondary reactions depends on the pyrolysis conditions as well as on the type of the pyrolysis reactor used. Secondary reactions are generally favored by high residence times and high temperatures. As it is practically impossible to achieve a completely oxygen-free atmosphere, there will be a small amount of oxidation reactions as well. The yields of the pyrolysis products are due to both the primary decomposition reactions of the raw material and the subsequent secondary reactions of the primary volatiles.

A process similar to the pyrolysis process takes place to some extent in nature, where organic substances of biological origin are buried and transformed into fossil fuels and coals of progressively higher carbon content under the action of temperature, pressure and chemical agents [ 1 ].

The simplest example of pyrolysis is food cooking. When food is cooked, the temperature of food increases leading to higher molecular vibrations and breakdown of larger complex molecules into smaller and simpler molecules which are easier to digest. Another example of pyrolysis is the pyrolysis of tobacco, paper and additives, in cigarettes and other products, which generates many volatile products including nicotine, carbon monoxide and tar that are responsible for the aroma and the hazardous health effects of smoking.

The word &#;pyrolysis&#; is coined from two Ancient Greek words pyro (πυρο) meaning fire and lysis (λύσις) meaning separating (or solution), so pyrolysis means separation by fire or heat. In photolysis, by contrast, the chemical substances are treated with light rather than heat.

Pyrolysis, or thermolysis, is in essence an irreversible thermochemical treatment process of complex solid or fluid chemical substances at elevated temperatures in an inert or oxygen-free atmosphere, where the rate of pyrolysis is temperature-dependent and it increases with temperature. During pyrolysis the molecules are subjected to very high temperatures leading to very high molecular vibrations at which the molecules are stretched and shaken to such an extent that they start breaking down into smaller molecules. Pyrolysis also is always the first step in other processes such as gasification and combustion where partial or total oxidation of the treated material occurs. Thermochemical treatment processes are generally classified according to their equivalence ratio (ER), which is defined as the amount of air added relative to the amount of air required for stoichiometric combustion. The equivalence ratio for pyrolysis is 0 (ER = 0), whereas the equivalence ratio for combustion is equal to or greater than 1 ( ER &#; 1 ), and the equivalence ratio for gasification varies between 0.25 and 0.50 ( Er = 0.25 &#; 0.50 ).

Advertisement

2. Industrial applications of pyrolysis

Pyrolysis is a proven and energetically efficient chemical technology that is used heavily in the chemical industry. Pyrolysis may be used in biorefineries for making a wide range of products and materials on which a future sustainable society may be based including many forms of carbon, fuels and other potentially valuable chemicals and chemical feedstocks.

There are a great many pyrolysis processes used in the production of fuels and chemicals. Such processes differ in the type of process, the use of catalysts, the substances treated and the end products. Pyrolysis processes include catalytic and noncatalytic pyrolysis, hydrous pyrolysis, vacuum pyrolysis, slow pyrolysis, torrefaction, fast pyrolysis, fluidized bed pyrolysis, flash pyrolysis, microwave-induced pyrolysis, plasma pyrolysis, empty tube pyrolysis, on-line pyrolysis and ultrasonic spray pyrolysis (USP). Other pyrolysis processes include also thermal decomposition, destructive and dry distillation, charring, tyre recycling and pyrolysis, liquefaction, high- and low-temperature carbonization, coking and thermal and catalytic cracking.

Common pyrolysis methods are frequently associated with many disadvantages including low gas yield, reducing the total energy value of the gas, and high content of tar in the gas, causing corrosion problems in the gas collection equipment and increasing the need for further treatment of the gas produced [6, 10, 11]. The disadvantages of the traditional pyrolysis methods may be overcome by radio-frequency plasma pyrolysis technology or by adding catalysts and steam.

Compared with noncatalytic pyrolysis, catalytic pyrolysis increases the pyrolytic gas and char yields but decreases the amount of oil [12]. The hydrogen concentration of the pyrolytic gas can also be considerably increased by the use of some catalysts [13]. The effect of the use of catalysts on the pyrolytic gas yield was investigated by Chen et al. It was found that some catalysts, particularly chromium oxide, have a strong positive influence on the pyrolytic gas, while other catalysts such as CuO even inhibits the pyrolytic gas yield [14]. Catalytic pyrolysis affects also the chemical composition and characteristics of the bio-oil produced. With catalytic biomass pyrolysis, the need for costly condensation and re-evaporation procedures prior to bio-oil upgrading is essentially eliminated [15, 16]. The effect of the catalysts on the yields and structure of products, however, becomes less significant with increasing temperature [17, 18].

Hydrogen may also be used in the pyrolysis process to enhance the chemical reduction and suppress oxidation by the elemental oxygen in the feedstock. The use of hydrogen can also change the pyrolysis products distribution.

Different catalysts may be used in different catalytic processes including Pt&#;Rh alloy, nickel-based catalysts, chromium oxide, Co/Mo/Al2O3, solid phosphoric acid and zeolite [19]. In a study conducted on biomass pyrolysis in a fixed-bed reactor, chromium oxide was used leading to gas yield improvement [14]. Oxygenated products can be reduced by utilizing zeolite-type catalysts [20]. Because of their high surface area and regular pore structures, mesoporous zeolites tend to inhibit repolymerization reactions [21, 22]. Zeolite catalyst was used in a catalytic pyrolysis process for the production of bio-oil from rice straw in a fluidized bed reactor. The water content in the bio-oil increased due to deoxygenation, and the aromatic compounds and the calorific value were also increased [12].

In hydrous or steam pyrolysis, organic materials are decomposed in the presence of superheated water or steam. The use of water as a pyrolyzing media also allows the feedstock to be introduced into the reactor in an aqueous form. The use of steam allows pyrolysis to occur at lower temperatures and higher pressures. In general, hydrous pyrolysis gives cleaner carbon with better properties and a relatively high surface area and porosity that are similar in nature to activated charcoal. The oil produced, however, contains high sulfur content and should normally be desulphurized. The C/H ratio of the pyrolytic oil is somewhat higher than that found for petroleum-derived fuels. This ratio indicates that such oil is a mixture of aliphatic and aromatic compounds. There is evidence to indicate that increasing the steam ratio (kg of steam/kg of biomass) leads to an almost linear increase of the calorific value of the biogas and an equally linear decrease in the calorific value of the biochar.

Bio-oils and fuels can be produced by hydrous pyrolysis of rice straw and other biomass materials. Steam cracking of petroleum oils can be used for the production of different cracking chemicals such as ethylene, which is a compound used for the production of many polymers and antifreeze (ethylene glycol).

According to Tu et al., radio-frequency plasma pyrolysis technology can overcome the disadvantages of common pyrolysis methods [23]. This is a capacitive dielectric heating method which employs an alternating current with high frequency and voltage to build up an electromagnetic field that produces plasma to induce the target material resulting in vigorous colliding, rubbing and thus self-heating. As the material is heated under a suitable degree of vacuum, pyrolysis occurs. The many advantages of this method include high heating rate, short heating time to reach the setting temperature, low heat loss, high concentration of syngas and low residual tar [5, 9, 24, 25, 26, 27]. The high heating rate can efficiently decompose the combustible solid to gas products of H2, CO, CH4 and low carbon hydrocarbons such as C2&#;C5 [23]. The low concentration of tar in the gas phase, mostly below 10 mg/Nm3, can be achieved because high-energy species, such as electrons, ions, atoms and free radicals, produced from the radio-frequency plasma can enhance the decomposition of tar [27].

In vacuum pyrolysis, the organic material is heated in vacuum to reduce its boiling point and also to avoid adverse chemical reactions.

In slow, or conventional, pyrolysis, the feedstock is heated slowly at a low heating rate (0.1 to 2°C per second) to low temperatures (<400°C) for a long period of time. During slow pyrolysis of biomass, the biomass is slowly devolatilized leading to the production of tar and char as the main products. The gas produced consists mainly of methane along with minor amounts of hydrogen, propane, ethylene, CO and CO2.

Torrefaction, also known as mild pyrolysis, is an example of a slow pyrolysis process. Torrefaction of biomass is a mild form of pyrolysis carried out under atmospheric conditions and at temperatures typically ranging between 200 and 320°C, where the onset of primary pyrolysis occurs at 200°C. For the low temperatures applied in torrefaction, the warm-up period is relatively short, even for the low heating rates commonly applied in torrefaction.

Torrefaction serves to improve the properties of biomass in relation to thermochemical processing techniques for energy generation such as combustion, co-combustion with coal or gasification. Torrefaction also eliminates all biological activity reducing the risk of fire and stopping biological decomposition. About 10% of the energy content in the biomass is lost as a result of the torrefaction process, but this energy of the volatiles can be used as a heating fuel for the process itself. During torrefaction, moisture and low-weight organic volatile components are removed, and the biomass loses typically 20% of its mass (dry bone basis). In addition, torrefaction partly depolymerizes the biopolymers (cellulose, hemicellulose and lignin) and the long polysaccharide chains, producing a hydrophobic, dry, blackened solid product as &#;torrefied biomass&#; or &#;bio-coal&#; with an increased energy density (on a mass basis) and greatly increased grindability. As a result, significantly lower energy is required to process the torrefied fuel, and it no longer requires separate handling facilities when co-fired with coal in existing power stations [20]. Torrefied or so-called roasted wood has found applications as a barbecue fuel and firelighter [28]. Finally, it has been suggested that torrefied biomass is a suitable feedstock for systems previously not considered feasible for raw biomass solid fuels such as entrained flow gasification. This is because torrefied biomass forms more spherical-shaped particles during grinding or milling [29].

In fast pyrolysis, on the other hand, the organic materials are rapidly heated at 450&#;600°C in the absence of air in which fast heat transfer (100&#;°C/s) is applied. Achieving very high heating and heat transfer rates during pyrolysis usually requires a finely ground biomass feed. Fast pyrolysis is a well-known technique for the production of high-volatile products. Due to the short vapor residence times, products are high-quality ethylene-rich gases which can be used subsequently to produce alcohols or gasoline. The production of char and tar is considerably less in this process [30, 31].

The fast pyrolysis process has been progressively designed and optimized for producing bio-oils from biomass. A number of essential features are required for the production of bio-oil by fast pyrolysis. These include very high heating rates (°C/s), high heat transfer rates (600&#; W/cm2), short vapor residence times (typically less than 2 seconds), lower process temperatures and efficient and rapid quenching of the condensable vapors in order to prevent their cracking and hence maximize oil production [6, 32]. In experiments conducted by Lee et al., the optimum reaction temperature range for the production of bio-oil by fast pyrolysis was found to be 410&#;510°C [33]. The bio-oil produced by such a process may contain large molecules derived from lignin which adversely affects the bio-oil properties [34, 35].

Catalytic fast pyrolysis can be used to produce aromatics using a range of different lignocellulosic feedstocks. Catalytic fast pyrolysis has several advantages over other biomass conversion processes where pyrolysis reactions can occur in a single reactor using inexpensive aluminosilicate catalysts [36].

With the application of induction heating, a fast pyrolysis process was used for producing valuable products from rice straw, sugarcane bagasse and coconut shell in an externally heated fixed-bed reactor [37]. In one process, the straw is pulverized, dried at 150°C, mixed with other raw materials, press formed at 200°C and finally carbonized at 300&#;350°C [38]. In another process, the biomass mixture, after pulverization and extrusion, is oven dried and carbonized at 600&#;800°C [39].

Infrared radiation is an efficient technique for fast heating processes since the energy from the infrared radiation is directly transferred to the process material. Infrared radiation is used as the heating source for many applications such as food processing, surface heating, solid decomposition and fast pyrolysis of oil shale [40]. In a study by Siramard et al. on the pyrolysis of shale oil in a fixed-bed reactor with infrared heating, it was found that shale oil production is affected by the direction of the infrared beam with higher yield achieved by the cross-current in comparison with the co-current heating. This is to be explained by the fact that the residence time of the volatiles was shorter in the case of the cross-current which led to the reduction of secondary cracking reactions of the volatiles. Reduced pyrolysis pressure was also found to be beneficial to the release of volatiles and the reduction of secondary cracking reactions [40].

Fluidized bed pyrolysis is carried out in a fluidized bed created by passing an upwardly moving carrier gas stream through a bed of the solid particulate substance under appropriate conditions to cause the solid/fluid mixture to behave as a fluid. The use of a carrier gas for fluidization results in a lower calorific value of the biogas produced. A fluidized bed reactor operating at atmospheric pressure at 500°C was used to produce bio-oils from wood feedstocks and rice straw [41]. A circulating fluidized bed reactor with sand used as bed material was used at a gauge pressure of about 5&#;15 kPa for the production of pyrolysis oil from napier grass (Pennisetum purpureum) with a calorific value of 19.79 MJ/kg. The maximum pyrolysis oil production was 37 wt% at 480°C of bed temperature. The oil produced is applicable to steam engines and gas turbine engines but not to diesel engines [42].

Higher efficiency is sometimes achieved by flash pyrolysis, also called anhydrous pyrolysis. In this process, the starting material is finely divided or crushed and quickly heated to between 350 and 500°C for less than 2 seconds, generally in vacuum in order to decrease the boiling point of the byproducts and avoid adverse chemical reactions. In this process, the insulating char layer that forms at the surface of the reacting particles is continuously removed. This process is used, for example, in organic synthesis.

A flash pyrolysis process was developed by Longanbach and Bauer to produce liquid fuels, chars and gases from bituminous and subbituminous coal, municipal refuse, grass straw and other biomass materials. In this process, the biomass material is heated by contact with hot recycle char and carried in gas stream through a reactor where pyrolysis occurs at very short residence times and heat-up rates [43]. A flash pyrolysis process was also developed to convert municipal, industrial and agricultural wastes into pyrolytic oil at near ambient pressure with no need for chemicals or catalysts. At the same time, inorganics were recovered [44].

Microwave heating is an electromagnetic irradiation in the range of wavelengths from 0.01 to 1 m and the equivalent frequency range of 0.3&#;300 GHz. Normally, the microwave reactors for chemical synthesis and all domestic microwave ovens operate at 2.45 GHz frequency, which corresponds to a wavelength of 12.25 cm. The material which absorbs microwave irradiation is known as microwave dielectrics, and microwave heating is thus referred to sometimes as dielectric heating [45, 46].

Microwave heating has been widely used in many areas of thermochemical treatment of waste materials such as biomass, waste cooking oil and scrap tyres. This is mainly due to its high heating efficiency and easy operation. Microwave heating is an inside heating process that is carried out within the heated sample as a whole. It requires in general less energy input than conventional heating and has in addition other advantages including heating uniformity and shorter heating time [47]. In microwave-induced pyrolysis, focussed heating by microwaves makes the resulting pyrolysis different from the traditional pyrolysis. Microwave-induced pyrolysis does not require in general agitation, fluidization or a high degree of grinding, and, furthermore, it can be used for the treatment of mixed feedstocks such as municipal solid wastes [48].

According to Huang et al., higher microwave power levels contribute to higher heating rates and reaction temperatures and can therefore produce a torrefied biomass with higher calorific value and lower H/C and O/C ratios [49]. The suitable microwave power levels proposed by Wang et al. are to be set between 250 and 300 W for the torrefaction of rice husk and sugarcane residues [50]. In a study by Ahmad et al., torrefied palm kernel shell had the highest calorific value at the microwave power level of 450 W. However, when the microwave power level increased from 450 to 600 W, the calorific value of the torrefied mass decreased [45].

A work by Zhu et al. has shown that microwave heating can change the supermolecular structure of lignocellulosic materials [51]. In a study by Huang et al., it was suggested that a hydrogen-rich fuel gas (51&#;55% H2) can be produced from rice straw using microwave-induced pyrolysis. The major components in the gaseous product were H2, CO2, CO and CH4. Alkanes, polars and low-ringed polycyclic aromatic hydrocarbons were the three primary kinds of compounds in the liquid product. From the viewpoint of energy consumption, close to 60% of the input energy could be derived and utilized as bioenergy [52].

Bio-oils of viscosities lower than the viscosity of light and heavy fuel oil and therefore easier to handle and process were obtained by microwave-assisted pyrolysis of aspen, canola and corncob feedstocks [41].

Microwave heating was also used for the treatment of waste tyres. Experiments were run in a batch laboratory scale with an oven operating at a frequency of 2.45 GHz with a variable energy output up to 6 kW. Short pyrolysis time and manageable product properties were achieved. Typical products were a solid residue containing up to 92% of carbon, a low-viscosity oil with a high calorific value and a gas containing light hydrocarbons, hydrogen and only traces of N2 [53].

In empty tube pyrolysis, a heated alumina or nickel tube is used in which the samples are injected. This method was developed simultaneously by two groups working at the Scottish Crop Research Institute and at Indiana University.

In ultrasonic spray pyrolysis (USP), an ultrasonic nozzle is utilized for fine chemical synthesis such as the synthesis of nanoparticles, zirconia and oxides.

Liquefaction is the thermochemical conversion of an organic solid into a liquid composed of heavy molecular compounds with characteristics similar to petroleum-based liquids such as fuel oils. Liquefaction may also involve the production of a liquid from a pyrolytic gas stream.

The materials treated by pyrolysis include:

  • Solid materials such as oil shale, coal, wood, woody and herbaceous biomass and organic, agricultural and municipal solid waste materials including straw, animal dung and human fecal waste, waste plastics and even waste printed circuit boards. Rice straw in particular has several characteristics that make it an attractive lignocellulosic material for bioethanol production, such as high cellulose and hemicellulose content that can be readily hydrolysed into fermentable sugars. The high ash and silica content of rice straw, however, makes the selection of an appropriate pretreatment technique a major challenge in developing an economically viable technology for bioethanol production [54].

  • Liquid materials such as petroleum fractions.

    The company is the world’s best Pyrolysis Machine supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.

23

0

Comments

Please Join Us to post.

0/2000

All Comments ( 0 )

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us!

Your Name: (required)

Your Email: (required)

Subject:

Your Message: (required)