5 Must-Have Features in a Hard Chrome Plating Equipment

5 necessary auxiliary machines for electroplating industry:

Filter and recycle filter equipment:

In order to ensure electroplating quality, the plating solution is required to filter regularly. While filter is the most commonly used filtration device in the chemical industry, and some kinds of electroplating also required ceaselessly cycling filtration on running. We can select the right filter based on plating situation and electroplating bath size as well as technological requirements.

You will get efficient and thoughtful service from Ruisite.

Cathode moving or agitation device:

Some or most of plating, the cathode shall in condition of moving states, then the operating current can be increased, while bath solution give deserved function (usually brightness and dispersion capacity), and can prevent from cusp, corner gross plated, charred. But some types of plating can use equipment or agitation device to replace cathode moving. Mechanical agitation is a mixer which made of corrosion-resistant material, usually, it is driven by motor, but its speed is can not too high. While air stirring adopts the deoiled compressed air after filtering.

Heating or cooling machines:

Because of plating solution working at a certain temperature, so electroplating bath shall be equipped with heating devices. For example, temperature of brightness nickel plating should be maintained at 50 &#;, while chrome plating temperature is 50 ~ 60 &#;, but brightness acidity copper electroplating or brightness silver plating required temperature within 30 &#;. Thus, these requirements shall be met by means of heat exchange machinery. For heating, normally use direct heating method.

Plating bath:

Plating bath must be equipped with accessories including anode and anode or anode baskets or anode hook, electrode rods , power cables, etc..
Most anode basket used titanium as material, a few species electroplating adopt stainless steel or steel.
Electrode rod is conductive rod which used for hanging anode and cathode and also connected to power source. Usually made of copper or brass rod, slightly longer than the plating bath, the diameter size according to the current demand, but the diameter at least more than 5cm.
The key function of power cable is to ensure can go through needed current. The best material is copper plate, also multi-strand cable can be adopted, but cross sectional area requirements must be complied with.

Plating hanger:

Hanger is the most important auxiliary tools for electroplating process. It is tool not only to make sure plating workpiece connected with cathode, but also has a direct impact on coating layer distribution and efficiency. Now there are professional hanger suppliers to offer general design hanger and also can customize according to users&#; special requirements.

Want more information on Hard Chrome Plating Equipment? Feel free to contact us.

Chrome plating process

Surface pre-treatment

The workpiece to be treated must have the smallest possible roughness depth of Rz 2 &#; 3 μm, as the hard chrome layer does not cover any scratches, pores or structural defects. For this reason, the workpiece is ground or belt polished in preparation. It should also be noted that the material must be metallically bright before treatment. This is the only way to ensure adequate protection.

Process steps

In hard chrome plating, the workpiece is electrolytically coated with the chrome layer in an electroplating bath. The process temperatures here are usually between 50 and 60° C. A rectifier is used to reduce the chromium ions to metallic chromium. This supplies the electrons needed for the process. In this way, chromium is only deposited at the points opposite an electrode (anode). As is usual in electric baths, edges build up due to the field line distribution at the points favored by the current. However, this can be reduced with the help of a special rack.

The required thickness of the chrome layer is decisive for the subsequent chemical and mechanical stress. The following layer thicknesses are applied:

• A layer thickness of 5 to 15 μm is applied in case of light wear. In addition, such a layer thickness serves to reduce friction.
• Hard chrome coatings of 15 to 30 μm protect against moderate wear.
• For adhesive wear resistance, a layer of 30 to 60 μm is applied to the workpiece.
• For heavy wear resistance, a chromium layer of 60 to 150 μm is used.
• To protect against abrasion and erosion as well as heavy wear, layer thicknesses of 150 to 350 μm are used.
• Chrome layers of over 250 μm are used for repair parts.

The properties of the hard chrome surface after treatment

The main focus of the procedure is to improve the wear resistance of the workpiece. In addition, the hard chrome layer gives the workpiece a hardness of 900 &#; HV without distortion. The hard chrome plating makes the surface water and dirt repellent, which further improves the corrosion resistance of the workpiece. Also, the machined workpieces have low adhesion and a minimal coefficient of friction.

In summary, the workpiece has the following advantages after treatment:

• no material distortion, despite high hardness
• high wear resistance and abrasion resistance
• low coefficient of friction and low adhesion tendency
• improved protection against chemical stress
• extended service life
• higher corrosion protection
• improvement of tribological properties

Industrial Applications

Hard chromium plating is suitable for a wide range of applications and metals. These include stainless steel, aluminum, non-ferrous metals and their alloys. Due to its excellent chemical, technical and mechanical characteristics, the process is important for a wide range of industries:

• Cylinders in the printing industry: To ensure the highest print quality, it is of great importance that the cylinders have a flawless surface. Dimensional accuracy in the micrometer scale also plays a crucial role. Furthermore, the cylinders must have strong corrosion protection, as the inks and cleaning agents used are often very aggressive. For these reasons, optimized hard chrome coatings are typically used here. Other possible applications for hard chrome coatings in the printing industry are duct rollers and metering rollers.
• Screen baskets for waste material processing in the paper industry: The screen baskets used must have a high level of wear protection as well as good repairability. Hard chrome plating is the best choice here. Other possible applications of hard chrome plating in the paper industry are creeping cylinders, applicator and ink metering rollers.
• Pistons in mechanical engineering: Hard chrome plating is used for piston rings and piston ring grooves, as high wear protection is required here. Hard chrome plating is also used in mechanical engineering for various tools, shafts and measuring rollers.

The process is also used in the foil, automotive and food industries.

CORROSION AND WEAR PROTECTION WITH BORTEC SOLUTIONS

BorTec&#;s various solutions also offer you excellent corrosion and wear protection. With the help of our patented BORINOX® PROCESS FOR HARDENING STAINLESS STEEL, you not only increase the hardness of your workpieces, but also protect them from distortion and cold welding.

BOROCOAT® is a thermochemical diffusion process that allows you to significantly increase the wear resistance of your material by adding a boride layer.

The NICKELCOAT® PROCESS FOR NICKEL plating offers you another possibility to protect your workpieces against wear. For expert advice, contact us today.

If you want to learn more, please visit our website barrel nickel plating machine.